Product ITEM is unavailable. See products from the same category below.
High-Speed Steel Straight-Flute Hand Taps
High-speed steel taps provide good wear resistance in general purpose tapping applications in a range of materials. Also called hand taps, high-speed steel straight-flute taps are turned with a tap wrench to create or repair internal threads in blind holes and through holes. As the taps are rotated into a hole to create threads, the chips move into the flutes but are not evacuated.
This hand tap is made of high speed steel and has a 9.32mm diameter, 1.7200 inch long shank. It is designed for use with steel, and meets the standards for USCTI, ANSI. This 5353 series hand tap has a TiN finish, and has metric measurements. It is non-coolant through, has right hand direction with a 85.72mm length. Plus it has four flutes and a straight shank.
This hand tap is made of high speed steel and has a 9.32mm diameter, 1.7200 inch long shank. It is designed for use with steel, and meets the standards for USCTI, ANSI. This 5353 series hand tap has a TiN finish, and has metric measurements. It is non-coolant through, has right hand direction with a 85.72mm length. Plus it has four flutes and a straight shank.
This straight flute tap is made of high speed steel and has a 5 mm diameter, 1½ inch long shank. It is designed for use with steel, and meets the standards for ANSI. This 5353 series straight flute tap has a TiN finish, and has metric measurements. It is non-coolant through, has right hand direction with a 60 mm length. Plus it has four flutes and a straight shank.
This straight flute tap is made of high speed steel and has a 5 mm diameter, 1½ inch long shank. It is designed for use with steel, and meets the standards for ANSI. This 5353 series straight flute tap has a TiN finish, and has metric measurements. It is non-coolant through, has right hand direction with a 60 mm length. Plus it has four flutes and a straight shank.
This hand tap is made of high speed steel and has a 8 mm diameter, 1.5900 inch long shank. It is designed for use with steel, and meets the standards for USCTI, ANSI. This 5353 series hand tap has a TiN finish, and has metric measurements. It is non-coolant through, has right hand direction with a 69.05mm length. Plus it has four flutes and a straight shank.
This hand tap is made of high speed steel and has a 8 mm diameter, 1.5900 inch long shank. It is designed for use with steel, and meets the standards for USCTI, ANSI. This 5353 series hand tap has a TiN finish, and has metric measurements. It is non-coolant through, has right hand direction with a 69.05mm length. Plus it has four flutes and a straight shank.
This hand tap is made of high speed steel and has a 0.255 inch diameter, 1½ inch long shank. It is for use with steel, and meets the standards for USCTI Table 302, ANSI. This 5305L/5303L series hand tap has a bright (uncoated) finish, and has fractional inch measurements. It is non-coolant through, has left hand direction with a 2½ inch length. Plus it has four flutes and a straight shank.
This hand tap is made of high speed steel and has a 0.255 inch diameter, 1½ inch long shank. It is for use with steel, and meets the standards for USCTI Table 302, ANSI. This 5305L/5303L series hand tap has a bright (uncoated) finish, and has fractional inch measurements. It is non-coolant through, has left hand direction with a 2½ inch length. Plus it has four flutes and a straight shank.
This hand tap is made of high speed steel and has a 0.590 inch diameter, 2¼ inch long shank. It is for use with steel, and meets the standards for USCTI Table 302, ANSI. This 5305L/5303L series hand tap has a bright (uncoated) finish, and has fractional inch measurements. It is non-coolant through, has left hand direction with a 4¼ inch length. Plus it has four flutes and a straight shank.
This hand tap is made of high speed steel and has a 0.590 inch diameter, 2¼ inch long shank. It is for use with steel, and meets the standards for USCTI Table 302, ANSI. This 5305L/5303L series hand tap has a bright (uncoated) finish, and has fractional inch measurements. It is non-coolant through, has left hand direction with a 4¼ inch length. Plus it has four flutes and a straight shank.
This hand tap is made of vanadium high speed steel and has a 0.381 inch diameter, 1.6900 inch long shank. It is designed for use with steel, and meets the standards for ANSI 302. This 5303/2303 series hand tap has a TiN finish, and has fractional inch measurements. It is non-coolant through, has right hand direction with a 2-15/16 inch length. Plus it has four flutes and a straight shank.
This hand tap is made of vanadium high speed steel and has a 0.381 inch diameter, 1.6900 inch long shank. It is designed for use with steel, and meets the standards for ANSI 302. This 5303/2303 series hand tap has a TiN finish, and has fractional inch measurements. It is non-coolant through, has right hand direction with a 2-15/16 inch length. Plus it has four flutes and a straight shank.
This straight flute tap is made of high speed steel and has a 0.367 inch diameter, 1.7200 inch long shank. It is for use with steel, and meets ANSI standards 302. This 5303/2303 series straight flute tap has a black oxide finish, and has fractional inch measurements. It is non-coolant through, has right hand direction with a 3⅜ inch length. Plus it has four flutes and a straight shank.
This straight flute tap is made of high speed steel and has a 0.367 inch diameter, 1.7200 inch long shank. It is for use with steel, and meets ANSI standards 302. This 5303/2303 series straight flute tap has a black oxide finish, and has fractional inch measurements. It is non-coolant through, has right hand direction with a 3⅜ inch length. Plus it has four flutes and a straight shank.
This straight flute tap is made of high speed steel and has a 0.194 inch diameter, 1½ inch long shank. It is designed for use with steel, and meets the standards for ANSI 302. This 5305/2305 series straight flute tap has a black oxide finish, and has pipe measurements. It is non-coolant through, has right hand direction with a 2⅜ inch length. Plus it has four flutes and a straight shank.
This straight flute tap is made of high speed steel and has a 0.194 inch diameter, 1½ inch long shank. It is designed for use with steel, and meets the standards for ANSI 302. This 5305/2305 series straight flute tap has a black oxide finish, and has pipe measurements. It is non-coolant through, has right hand direction with a 2⅜ inch length. Plus it has four flutes and a straight shank.
This straight flute tap is made of high speed steel and has a 13.70mm diameter, 2.4400 inch long shank. It is for use with aluminum, brass, bronze, copper, and meets ANSI standards. This 7353 series straight flute tap has a bright finish, and has metric measurements. It is non-coolant through, has right hand direction with a 102mm length. Plus it has four flutes and a straight shank.
This straight flute tap is made of high speed steel and has a 13.70mm diameter, 2.4400 inch long shank. It is for use with aluminum, brass, bronze, copper, and meets ANSI standards. This 7353 series straight flute tap has a bright finish, and has metric measurements. It is non-coolant through, has right hand direction with a 102mm length. Plus it has four flutes and a straight shank.
This hand tap is made of high speed steel and has a 0.194 inch diameter, 1.9 inch long shank. It is for use with aluminum, brass, bronze, copper, stainless steel, steel, and meets the standards for USCTI Table 302, ANSI. This 5305L/5303L series hand tap has a bright (uncoated) finish, and has pipe measurements. It has right hand direction with a 2⅜ inch length, plus it has four flutes.
This hand tap is made of high speed steel and has a 0.194 inch diameter, 1.9 inch long shank. It is for use with aluminum, brass, bronze, copper, stainless steel, steel, and meets the standards for USCTI Table 302, ANSI. This 5305L/5303L series hand tap has a bright (uncoated) finish, and has pipe measurements. It has right hand direction with a 2⅜ inch length, plus it has four flutes.
This hand tap is made of high speed steel and has a 0.318 inch diameter, 1.5900 inch long shank. It is for use with steel, and meets the standards for USCTI Table 302, ANSI. This 5305L/5303L series hand tap has a bright (uncoated) finish, and has fractional inch measurements. It is non-coolant through, has left hand direction with a 2-23/32 inch length. Plus it has four flutes and a straight shank.
This hand tap is made of high speed steel and has a 0.318 inch diameter, 1.5900 inch long shank. It is for use with steel, and meets the standards for USCTI Table 302, ANSI. This 5305L/5303L series hand tap has a bright (uncoated) finish, and has fractional inch measurements. It is non-coolant through, has left hand direction with a 2-23/32 inch length. Plus it has four flutes and a straight shank.
This hand tap is made of high speed steel and has a 0.323 inch diameter, 1.7200 inch long shank. It is for use with steel, and meets the standards for USCTI Table 302, ANSI. This 5305L/5303L series hand tap has a bright (uncoated) finish, and has fractional inch measurements. It is non-coolant through, has left hand direction with a 3-5/32 inch length. Plus it has four flutes and a straight shank.
This hand tap is made of high speed steel and has a 0.323 inch diameter, 1.7200 inch long shank. It is for use with steel, and meets the standards for USCTI Table 302, ANSI. This 5305L/5303L series hand tap has a bright (uncoated) finish, and has fractional inch measurements. It is non-coolant through, has left hand direction with a 3-5/32 inch length. Plus it has four flutes and a straight shank.
This hand tap is made of high speed steel and has a 0.590 inch diameter, 2¼ inch long shank. It is for use with steel, and meets the standards for USCTI Table 302, ANSI. This 5305L/5303L series hand tap has a bright (uncoated) finish, and has fractional inch measurements. It is non-coolant through, has left hand direction with a 4¼ inch length. Plus it has four flutes and a straight shank.
This hand tap is made of high speed steel and has a 0.590 inch diameter, 2¼ inch long shank. It is for use with steel, and meets the standards for USCTI Table 302, ANSI. This 5305L/5303L series hand tap has a bright (uncoated) finish, and has fractional inch measurements. It is non-coolant through, has left hand direction with a 4¼ inch length. Plus it has four flutes and a straight shank.
This hand tap is made of high speed steel and has a 0.480 inch diameter, 2 inch long shank. It is for use with steel, and meets the standards for USCTI Table 302, ANSI. This 5305L/5303L series hand tap has a bright (uncoated) finish, and has fractional inch measurements. It is non-coolant through, has left hand direction with a 3-13/16 inch length. Plus it has four flutes and a straight shank.
This hand tap is made of high speed steel and has a 0.480 inch diameter, 2 inch long shank. It is for use with steel, and meets the standards for USCTI Table 302, ANSI. This 5305L/5303L series hand tap has a bright (uncoated) finish, and has fractional inch measurements. It is non-coolant through, has left hand direction with a 3-13/16 inch length. Plus it has four flutes and a straight shank.
This straight flute tap is made of high speed steel and has a 0.480 inch diameter, 2 inch long shank. It is for use with steel, and meets ANSI standards 302. This 5303/2303 series straight flute tap has a black oxide finish, and has fractional inch measurements. It is non-coolant through, has right hand direction with a 3 13/16 inch length. Plus it has four flutes and a straight shank.
This straight flute tap is made of high speed steel and has a 0.480 inch diameter, 2 inch long shank. It is for use with steel, and meets ANSI standards 302. This 5303/2303 series straight flute tap has a black oxide finish, and has fractional inch measurements. It is non-coolant through, has right hand direction with a 3 13/16 inch length. Plus it has four flutes and a straight shank.
This straight flute tap is made of high speed steel and has a 0.381 inch diameter, 1.6900 inch long shank. It is for use with steel, and meets ANSI standards 302. This 5303/2303 series straight flute tap has a black oxide finish, and has fractional inch measurements. It is non-coolant through, has right hand direction with a 2-15/16 inch length. Plus it has four flutes and a straight shank.
This straight flute tap is made of high speed steel and has a 0.381 inch diameter, 1.6900 inch long shank. It is for use with steel, and meets ANSI standards 302. This 5303/2303 series straight flute tap has a black oxide finish, and has fractional inch measurements. It is non-coolant through, has right hand direction with a 2-15/16 inch length. Plus it has four flutes and a straight shank.
To view Availability for another location, please enter postal code below
Availability dates may vary based on the assortment of product in the cart and is not final until you complete your order.
