Product ITEM is unavailable. See products from the same category below.
Retaining-Ring Pliers & Sets
Retaining-ring pliers install and remove snap rings that fit into a bore or onto a shaft and hold components in place. Also known as circlip pliers, their tips provide a firm grip on the rings to prevent them from flying off. Each pair of pliers adjusts its jaws to accommodate rings within a set diameter range. Retaining-ring pliers are commonly used to place rings on actuators, gear assemblies, motor shafts, and other machinery.
This Proto series retaining ring plier set has a length of 6 inch, 7¼ inch. The handle is red. It features no screws to tighten. In addition, it is non-sparking, with a standard cushion grip. This retaining ring plier set includes two retaining ring convertible pliers 6 inch, two retaining ring convertible pliers 7¼ inch.
This Proto series retaining ring plier set has a length of 6 inch, 7¼ inch. The handle is red. It features no screws to tighten. In addition, it is non-sparking, with a standard cushion grip. This retaining ring plier set includes two retaining ring convertible pliers 6 inch, two retaining ring convertible pliers 7¼ inch.
This retaining ring pliers has a length of 6 inch, plus it weighs 0.19 pounds. The handle is red. It features precision ground tips and meets the standards for ASME B107.500-2010. In addition, it is non-sparking, with a standard cushion grip.
This retaining ring pliers has a length of 6 inch, plus it weighs 0.19 pounds. The handle is red. It features precision ground tips and meets the standards for ASME B107.500-2010. In addition, it is non-sparking, with a standard cushion grip.
This retaining ring pliers has a length of 7¼ inch, plus it weighs 0.33 pounds. The handle is red. It features precision ground tips and meets the standards for ASME B107.500-2010. In addition, it is non-sparking, with a standard cushion grip.
This retaining ring pliers has a length of 7¼ inch, plus it weighs 0.33 pounds. The handle is red. It features precision ground tips and meets the standards for ASME B107.500-2010. In addition, it is non-sparking, with a standard cushion grip.
Convertible snap ring pliers convert from internal to external or vice versa. Fixed tips are precision formed and induction hardened for accurate fit and long wear. Tip angle 90 degrees. Tip size 0.090 inch. Length 8-5/8 inches.
Convertible snap ring pliers convert from internal to external or vice versa. Fixed tips are precision formed and induction hardened for accurate fit and long wear. Tip angle 90 degrees. Tip size 0.090 inch. Length 8-5/8 inches.
Convertible snap ring pliers convert from internal to external or vice versa. Fixed tips are precision formed and induction hardened for accurate fit and long wear. Tip angle 90 degrees. Tip size 0.038 inch. Length 5-11/16 inches.
Convertible snap ring pliers convert from internal to external or vice versa. Fixed tips are precision formed and induction hardened for accurate fit and long wear. Tip angle 90 degrees. Tip size 0.038 inch. Length 5-11/16 inches.
Convertible snap ring pliers convert from internal to external or vice versa. Fixed tips are precision formed and induction hardened for accurate fit and long wear. Tip angle 0 degrees. Tip size 0.070 inch. Length 7-1/2 inches.
Convertible snap ring pliers convert from internal to external or vice versa. Fixed tips are precision formed and induction hardened for accurate fit and long wear. Tip angle 0 degrees. Tip size 0.070 inch. Length 7-1/2 inches.
Convertible snap ring pliers convert from internal to external or vice versa. Fixed tips are precision formed and induction hardened for accurate fit and long wear. Tip angle 90 degrees. Tip size 0.047 inch. Length 5-11/16 inches.
Convertible snap ring pliers convert from internal to external or vice versa. Fixed tips are precision formed and induction hardened for accurate fit and long wear. Tip angle 90 degrees. Tip size 0.047 inch. Length 5-11/16 inches.
This retaining ring pliers has a length of 6 inch, plus it weighs 0.19 pounds. The handle is red. It features precision ground tips and meets the standards for ASME B107.500-2010. In addition, it is non-sparking, with a standard cushion grip.
This retaining ring pliers has a length of 6 inch, plus it weighs 0.19 pounds. The handle is red. It features precision ground tips and meets the standards for ASME B107.500-2010. In addition, it is non-sparking, with a standard cushion grip.
5-3/8 inch internal retaining ring pliers. Tip angle 0 degrees. Tip size 0.038 inch. Shaft diameter 3/8 to 1 inch. Use with internal retaining rings. Fixed tips are precision formed and induction hardened for accurate fit and long wear.
5-3/8 inch internal retaining ring pliers. Tip angle 0 degrees. Tip size 0.038 inch. Shaft diameter 3/8 to 1 inch. Use with internal retaining rings. Fixed tips are precision formed and induction hardened for accurate fit and long wear.
Horseshoe washer lock ring pliers. For spreading both soft iron horse-shoe lock washers used on brakes and tempered steel lock rings used on gear and bearing shafts. With plastisol dipped handles. Length 7-13/16 inches.
Horseshoe washer lock ring pliers. For spreading both soft iron horse-shoe lock washers used on brakes and tempered steel lock rings used on gear and bearing shafts. With plastisol dipped handles. Length 7-13/16 inches.
Lock ring pliers-parallel jaw. For removal of lock snap rings used on bearing shafts. Compound leverage simplifies removal. Jaw tips are indented to hold ring ends and prevent breakage. Jaws spread 1-1/4inch Plastisol grips for added comfort.
Lock ring pliers-parallel jaw. For removal of lock snap rings used on bearing shafts. Compound leverage simplifies removal. Jaw tips are indented to hold ring ends and prevent breakage. Jaws spread 1-1/4inch Plastisol grips for added comfort.
To view Availability for another location, please enter postal code below
Availability dates may vary based on the assortment of product in the cart and is not final until you complete your order.
