General Purpose Spiral-Point Taps

This spiral point tap is made of high speed steel and has a 6 mm diameter, 40 mm long shank. It is designed for use with aluminum, cast iron, steel, and meets the standards for ANSI. This 142 series spiral point tap has an oxide finish, and has metric measurements. It is non-coolant through, has right hand direction with a 2-23/32 inch length. Plus it has two flutes and a straight shank.

This spiral point tap is made of high speed steel and has a 6 mm diameter, 40 mm long shank. It is designed for use with aluminum, cast iron, steel, and meets the standards for ANSI. This 142 series spiral point tap has an oxide finish, and has metric measurements. It is non-coolant through, has right hand direction with a 2-23/32 inch length. Plus it has two flutes and a straight shank.

This spiral point tap is made of high speed steel and has a 9.68mm diameter, 42 mm long shank. It is designed for use with aluminum, cast iron, steel, and meets ANSI standards. This 142 series spiral point tap has an oxide finish, and has metric measurements. It is non-coolant through, has right hand direction with a 2-15/16 inch length. Plus it has three flutes and a straight shank.

This spiral point tap is made of high speed steel and has a 9.68mm diameter, 42 mm long shank. It is designed for use with aluminum, cast iron, steel, and meets ANSI standards. This 142 series spiral point tap has an oxide finish, and has metric measurements. It is non-coolant through, has right hand direction with a 2-15/16 inch length. Plus it has three flutes and a straight shank.

This spiral point tap is made of high speed steel and has a 8.18mm diameter, 54 mm long shank. It is designed for use with aluminum, cast iron, steel, and meets ANSI standards. This 142 series spiral point tap has a bright finish, and has metric measurements. It is non-coolant through, has right hand direction with a 3-19/32 inch length. Plus it has three flutes and a straight shank.

This spiral point tap is made of high speed steel and has a 8.18mm diameter, 54 mm long shank. It is designed for use with aluminum, cast iron, steel, and meets ANSI standards. This 142 series spiral point tap has a bright finish, and has metric measurements. It is non-coolant through, has right hand direction with a 3-19/32 inch length. Plus it has three flutes and a straight shank.

This spiral point tap is made of high speed steel and has a 6.90mm diameter, 50 mm long shank. It is designed for use with aluminum, cast iron, steel, and meets the standards for ANSI. This 142 series spiral point tap has an oxide finish, and has metric measurements. It is non-coolant through, has right hand direction with a 86 mm length. Plus it has three flutes and a straight shank.

This spiral point tap is made of high speed steel and has a 6.90mm diameter, 50 mm long shank. It is designed for use with aluminum, cast iron, steel, and meets the standards for ANSI. This 142 series spiral point tap has an oxide finish, and has metric measurements. It is non-coolant through, has right hand direction with a 86 mm length. Plus it has three flutes and a straight shank.

This spiral point tap is made of high speed steel and has a 2.80mm diameter, 34 mm long shank. It is designed for use with aluminum, cast iron, steel, and meets the standards for ANSI. This 142 series spiral point tap has an oxide finish, and has metric measurements. It is non-coolant through, has right hand direction with a 46 mm length. Plus it has two flutes and a straight shank.

This spiral point tap is made of high speed steel and has a 2.80mm diameter, 34 mm long shank. It is designed for use with aluminum, cast iron, steel, and meets the standards for ANSI. This 142 series spiral point tap has an oxide finish, and has metric measurements. It is non-coolant through, has right hand direction with a 46 mm length. Plus it has two flutes and a straight shank.

This spiral point tap is made of high speed steel and has a 12.42mm diameter, 68 mm long shank. It is designed for use with aluminum, cast iron, steel, and meets ANSI standards. This 142 series spiral point tap has a bright finish, and has metric measurements. It is non-coolant through, has right hand direction with a 4-15/32 inch length. Plus it has three flutes and a straight shank.

This spiral point tap is made of high speed steel and has a 12.42mm diameter, 68 mm long shank. It is designed for use with aluminum, cast iron, steel, and meets ANSI standards. This 142 series spiral point tap has a bright finish, and has metric measurements. It is non-coolant through, has right hand direction with a 4-15/32 inch length. Plus it has three flutes and a straight shank.

This spiral point tap is made of high speed steel and has a 0.318 inch diameter, 1.5860 inch long shank. It is for use with aluminum, cast iron, steel, and meets ANSI standards. This 105 series spiral point tap has an oxide finish, and has fractional inch measurements. It is non-coolant through, has right hand direction with a 2-23/32 inch length. Plus it has two flutes and a straight shank.

This spiral point tap is made of high speed steel and has a 0.318 inch diameter, 1.5860 inch long shank. It is for use with aluminum, cast iron, steel, and meets ANSI standards. This 105 series spiral point tap has an oxide finish, and has fractional inch measurements. It is non-coolant through, has right hand direction with a 2-23/32 inch length. Plus it has two flutes and a straight shank.

This pipe tap is made of high speed steel and has a 0.194 inch diameter, 1.4960 inch long shank. It meets the standards for ANSI. This 105H series pipe tap has a bright (uncoated) finish, and has pipe measurements. It is non-coolant through, has right hand direction with a 2⅜ inch length. Plus it has two flutes and a straight shank.

This pipe tap is made of high speed steel and has a 0.194 inch diameter, 1.4960 inch long shank. It meets the standards for ANSI. This 105H series pipe tap has a bright (uncoated) finish, and has pipe measurements. It is non-coolant through, has right hand direction with a 2⅜ inch length. Plus it has two flutes and a straight shank.

This hand tap is made of high speed steel and has a 0.194 inch diameter, 1.5730 inch long shank. It meets the standards for ANSI. This 105 series hand tap has an oxide finish, and has pipe measurements. It is non-coolant through, has right hand direction with a 2⅜ inch length. Plus it has two flutes and a straight shank.

This hand tap is made of high speed steel and has a 0.194 inch diameter, 1.5730 inch long shank. It meets the standards for ANSI. This 105 series hand tap has an oxide finish, and has pipe measurements. It is non-coolant through, has right hand direction with a 2⅜ inch length. Plus it has two flutes and a straight shank.

This spiral point tap is made of high speed steel and has a 0.323 inch diameter, 1.8350 inch long shank. It is for use with aluminum, cast iron, steel, and meets ANSI standards. This 105 series spiral point tap has an oxide finish, and has fractional inch measurements. It is non-coolant through, has right hand direction with a 3-5/32 inch length. Plus it has three flutes and a straight shank.

This spiral point tap is made of high speed steel and has a 0.323 inch diameter, 1.8350 inch long shank. It is for use with aluminum, cast iron, steel, and meets ANSI standards. This 105 series spiral point tap has an oxide finish, and has fractional inch measurements. It is non-coolant through, has right hand direction with a 3-5/32 inch length. Plus it has three flutes and a straight shank.

This spiral point tap is made of high speed steel and has a 0.220 inch diameter, 1.5190 inch long shank. It meets the standards for ANSI. This 105 series spiral point tap has an oxide finish, and has pipe measurements. It is non-coolant through, has right hand direction with a 2⅜ inch length. Plus it has two flutes and a straight shank.

This spiral point tap is made of high speed steel and has a 0.220 inch diameter, 1.5190 inch long shank. It meets the standards for ANSI. This 105 series spiral point tap has an oxide finish, and has pipe measurements. It is non-coolant through, has right hand direction with a 2⅜ inch length. Plus it has two flutes and a straight shank.

This spiral point tap is made of high speed steel and has a 0.590 inch diameter, 2.5370 inch long shank. It is for use with aluminum, cast iron, steel, and meets ANSI standards. This 105 series spiral point tap has an oxide finish, and has fractional inch measurements. It is non-coolant through, has right hand direction with a 4¼ inch length. Plus it has three flutes and a straight shank.

This spiral point tap is made of high speed steel and has a 0.590 inch diameter, 2.5370 inch long shank. It is for use with aluminum, cast iron, steel, and meets ANSI standards. This 105 series spiral point tap has an oxide finish, and has fractional inch measurements. It is non-coolant through, has right hand direction with a 4¼ inch length. Plus it has three flutes and a straight shank.

This spiral point tap is made of high speed steel and has a 0.141 inch diameter, 1.3090 inch long shank. It is designed for use with steel, and meets the standards for ANSI. This 287 series spiral point tap has a bright finish, and has pipe measurements. It is non-coolant through, has right hand direction with a 1⅝ inch length. Plus it has two flutes and a straight shank.

This spiral point tap is made of high speed steel and has a 0.141 inch diameter, 1.3090 inch long shank. It is designed for use with steel, and meets the standards for ANSI. This 287 series spiral point tap has a bright finish, and has pipe measurements. It is non-coolant through, has right hand direction with a 1⅝ inch length. Plus it has two flutes and a straight shank.

This spiral point tap is made of high speed steel and has a 0.381 inch diameter, 1.6870 inch long shank. It is for use with aluminum, cast iron, steel, and meets ANSI standards. This 105 series spiral point tap has an oxide finish, and has fractional inch measurements. It is non-coolant through, has right hand direction with a 2-15/16 inch length. Plus it has three flutes and a straight shank.

This spiral point tap is made of high speed steel and has a 0.381 inch diameter, 1.6870 inch long shank. It is for use with aluminum, cast iron, steel, and meets ANSI standards. This 105 series spiral point tap has an oxide finish, and has fractional inch measurements. It is non-coolant through, has right hand direction with a 2-15/16 inch length. Plus it has three flutes and a straight shank.

Ce taraud est en acier rapide et a une tige de 0,194 po de diamètre/1,4960 po de long. Il est destiné à être utilisé avec de l'acier et répond aux normes ANSI. Il a un fini oxyde noir et des mesures de tuyaux. Il est sans canal de refroidissement, a une direction à droite et une longueur de 2 3/8 po. De plus, il a 2 cannelures et une tige droite.

Ce taraud est en acier rapide et a une tige de 0,194 po de diamètre/1,4960 po de long. Il est destiné à être utilisé avec de l'acier et répond aux normes ANSI. Il a un fini oxyde noir et des mesures de tuyaux. Il est sans canal de refroidissement, a une direction à droite et une longueur de 2 3/8 po. De plus, il a 2 cannelures et une tige droite.

Ce taraud est en acier rapide et a une tige de 0,194 po de diamètre/1,4960 po de long. Il est destiné à être utilisé avec de l'acier et répond aux normes ANSI. Il a un fini brillant et des mesures de tuyaux. Il est sans canal de refroidissement, a une direction à droite et une longueur de 2 3/8 po. De plus, il a 2 cannelures et une tige droite.

Ce taraud est en acier rapide et a une tige de 0,194 po de diamètre/1,4960 po de long. Il est destiné à être utilisé avec de l'acier et répond aux normes ANSI. Il a un fini brillant et des mesures de tuyaux. Il est sans canal de refroidissement, a une direction à droite et une longueur de 2 3/8 po. De plus, il a 2 cannelures et une tige droite.