Product ITEM is unavailable. See products from the same category below.
RTV Gasket Makers
RTV (room temperature vulcanizing) gasket makers have better gap-filling properties than anaerobic gasket makers which makes them more suited for assemblies that have wider gaps with surfaces that are not precision machined. They cure when exposed to air at room temperature, where anaerobic gasket makers cure in the absence of air. The liquid form of these gasket makers replaces the need for a precut material gasket by filling the space between two mating surfaces. Also called formed-in-place (FIP) gaskets, they seep into pits and scratches to provide a clean surface and create any shape needed. RTV gasket makers are lighter weight and thicker than cork, paper, or rubber gaskets.
This sensor-safe, room temperature vulcanizing gasket maker is designed for high torque applications. The non-corrosive, grey paste can withstand a temperature range of -59 to 329 Degrees C and has a flashpoint of greater than 93 Degrees C. The low odour sealant begins to harden in 30 minutes and fully cures in 24 hours. This product comes in a 190-millilitre tube.
This sensor-safe, room temperature vulcanizing gasket maker is designed for high torque applications. The non-corrosive, grey paste can withstand a temperature range of -59 to 329 Degrees C and has a flashpoint of greater than 93 Degrees C. The low odour sealant begins to harden in 30 minutes and fully cures in 24 hours. This product comes in a 190-millilitre tube.
This one-part, sensor-safe, room temperature vulcanizing gasket maker is designed for high-temperature applications. The non-corrosive, copper paste can withstand a temperature range of -54 to 371 Degrees C and has a flashpoint of greater than 93 Degrees C. The low odour sealant begins to harden in 60 minutes and fully cures in 24 hours. This product comes in an 80-millilitre tube.
This one-part, sensor-safe, room temperature vulcanizing gasket maker is designed for high-temperature applications. The non-corrosive, copper paste can withstand a temperature range of -54 to 371 Degrees C and has a flashpoint of greater than 93 Degrees C. The low odour sealant begins to harden in 60 minutes and fully cures in 24 hours. This product comes in an 80-millilitre tube.
This sensor-safe, room temperature vulcanizing gasket maker is designed for high torque applications. The non-corrosive, grey paste can withstand a temperature range of -59 to 329 Degrees C and has a flashpoint of greater than 93 Degrees C. The low odour sealant begins to harden in 30 minutes and fully cures in 24 hours. This product comes in an 80-millilitre tube.
This sensor-safe, room temperature vulcanizing gasket maker is designed for high torque applications. The non-corrosive, grey paste can withstand a temperature range of -59 to 329 Degrees C and has a flashpoint of greater than 93 Degrees C. The low odour sealant begins to harden in 30 minutes and fully cures in 24 hours. This product comes in an 80-millilitre tube.
This SI 5920 gasket maker is copper and comes in a 10.14 fluid ounce cartridge. It meets the standards for California Proposition 65, CEPA DSL/NDSL, CERCLA/SARA Section 302 EHS, CERCLA/SARA Section 311/312, CERCLA/SARA Section 313, OSHA 29 CFR 1910.1200, TSCA. This gasket maker has a working time of one hour.
This SI 5920 gasket maker is copper and comes in a 10.14 fluid ounce cartridge. It meets the standards for California Proposition 65, CEPA DSL/NDSL, CERCLA/SARA Section 302 EHS, CERCLA/SARA Section 311/312, CERCLA/SARA Section 313, OSHA 29 CFR 1910.1200, TSCA. This gasket maker has a working time of one hour.
This SI 587 gasket maker is blue and comes in a 2.37 fluid ounce tube. It meets the standards for California Proposition 65, CEPA DSL/NDSL, CERCLA/SARA Section 302 EHS, CERCLA/SARA Section 311/312, CERCLA/SARA Section 313, OSHA 29 CFR 1910.1200, TSCA. This gasket maker has a working time of 10 minutes.
This SI 587 gasket maker is blue and comes in a 2.37 fluid ounce tube. It meets the standards for California Proposition 65, CEPA DSL/NDSL, CERCLA/SARA Section 302 EHS, CERCLA/SARA Section 311/312, CERCLA/SARA Section 313, OSHA 29 CFR 1910.1200, TSCA. This gasket maker has a working time of 10 minutes.
This SI 5900 gasket maker is black and comes in a five ounce cartridge. It meets the standards for California Proposition 65, CEPA DSL/NDSL, CERCLA/SARA Section 302 EHS, CERCLA/SARA Section 311/312, CERCLA/SARA Section 313, OSHA 29 CFR 1910.1200, TSCA. This gasket maker has a working time of 15 minutes.
This SI 5900 gasket maker is black and comes in a five ounce cartridge. It meets the standards for California Proposition 65, CEPA DSL/NDSL, CERCLA/SARA Section 302 EHS, CERCLA/SARA Section 311/312, CERCLA/SARA Section 313, OSHA 29 CFR 1910.1200, TSCA. This gasket maker has a working time of 15 minutes.
This anaerobic gasket maker is made for use on rigid machined flange assemblies with less than a 0.010-inch gap. The purple-coloured gel fully cures in 24 hours and begins to harden in 10 minutes. It has a temperature range of -10 to 150 Degrees C and a flashpoint of 93 Degrees C. This methacrylate-based adhesive is resistant to low pressures and comes in a 50-millimetre tube.
This anaerobic gasket maker is made for use on rigid machined flange assemblies with less than a 0.010-inch gap. The purple-coloured gel fully cures in 24 hours and begins to harden in 10 minutes. It has a temperature range of -10 to 150 Degrees C and a flashpoint of 93 Degrees C. This methacrylate-based adhesive is resistant to low pressures and comes in a 50-millimetre tube.
This sealant comes in a tube. It meets the standards for UL 94 HB and CFIA. These RTV gasket makers replace the need for a precut gasket by filling the space between two mating surfaces. They cure in place and are useful for general purpose applications.
This sealant comes in a tube. It meets the standards for UL 94 HB and CFIA. These RTV gasket makers replace the need for a precut gasket by filling the space between two mating surfaces. They cure in place and are useful for general purpose applications.
This SI 587 gasket maker is blue and comes in a 10.14 fluid ounce cartridge. It meets the standards for California Proposition 65, CEPA DSL/NDSL, CERCLA/SARA Section 302 EHS, CERCLA/SARA Section 311/312, CERCLA/SARA Section 313, OSHA 29 CFR 1910.1200, TSCA. This gasket maker has a working time of 10 minutes.
This SI 587 gasket maker is blue and comes in a 10.14 fluid ounce cartridge. It meets the standards for California Proposition 65, CEPA DSL/NDSL, CERCLA/SARA Section 302 EHS, CERCLA/SARA Section 311/312, CERCLA/SARA Section 313, OSHA 29 CFR 1910.1200, TSCA. This gasket maker has a working time of 10 minutes.
This SI 5900 gasket maker is black and comes in a 10.14 fluid ounce cartridge. It meets the standards for California Proposition 65, CEPA DSL/NDSL, CERCLA/SARA Section 302 EHS, CERCLA/SARA Section 311/312, CERCLA/SARA Section 313, OSHA 29 CFR 1910.1200, TSCA. This gasket maker has a working time of 15 minutes.
This SI 5900 gasket maker is black and comes in a 10.14 fluid ounce cartridge. It meets the standards for California Proposition 65, CEPA DSL/NDSL, CERCLA/SARA Section 302 EHS, CERCLA/SARA Section 311/312, CERCLA/SARA Section 313, OSHA 29 CFR 1910.1200, TSCA. This gasket maker has a working time of 15 minutes.
This SI 598 gasket maker is black and comes in a 2.37 fluid ounce tube. It meets the standards for California Proposition 65, CEPA DSL/NDSL, CERCLA/SARA Section 302 EHS, CERCLA/SARA Section 311/312, CERCLA/SARA Section 313, OSHA 29 CFR 1910.1200, TSCA. This gasket maker has a working time of 30 minutes.
This SI 598 gasket maker is black and comes in a 2.37 fluid ounce tube. It meets the standards for California Proposition 65, CEPA DSL/NDSL, CERCLA/SARA Section 302 EHS, CERCLA/SARA Section 311/312, CERCLA/SARA Section 313, OSHA 29 CFR 1910.1200, TSCA. This gasket maker has a working time of 30 minutes.
This SI 5699 gasket maker is grey and comes in a 2.37 fluid ounce tube. It meets the standards for California Proposition 65CEPA DSL/NDSL, CERCLA/SARA Section 302 EHS, CERCLA/SARA Section 311/312, CERCLA/SARA Section 313, OSHA 29 CFR 1910.1200, TSCA. This gasket maker has a working time of 30 minutes.
This SI 5699 gasket maker is grey and comes in a 2.37 fluid ounce tube. It meets the standards for California Proposition 65CEPA DSL/NDSL, CERCLA/SARA Section 302 EHS, CERCLA/SARA Section 311/312, CERCLA/SARA Section 313, OSHA 29 CFR 1910.1200, TSCA. This gasket maker has a working time of 30 minutes.
This SI 5999 gasket maker is grey and comes in a 10.14 fluid ounce cartridge. It meets the standards for California Proposition 65, CEPA DSL/NDSL, CERCLA/SARA Section 302 EHS, CERCLA/SARA Section 311/312, CERCLA/SARA Section 313, OSHA 29 CFR 1910.1200, TSCA. This gasket maker has a working time of 10 minutes.
This SI 5999 gasket maker is grey and comes in a 10.14 fluid ounce cartridge. It meets the standards for California Proposition 65, CEPA DSL/NDSL, CERCLA/SARA Section 302 EHS, CERCLA/SARA Section 311/312, CERCLA/SARA Section 313, OSHA 29 CFR 1910.1200, TSCA. This gasket maker has a working time of 10 minutes.
This SI 5920 gasket maker is copper and comes in a 2.37 fluid ounce tube. It meets the standards for California Proposition 65, CEPA DSL/NDSL, CERCLA/SARA Section 302 EHS, CERCLA/SARA Section 311/312, CERCLA/SARA Section 313, OSHA 29 CFR 1910.1200, TSCA. This gasket maker has a working time of one hour.
This SI 5920 gasket maker is copper and comes in a 2.37 fluid ounce tube. It meets the standards for California Proposition 65, CEPA DSL/NDSL, CERCLA/SARA Section 302 EHS, CERCLA/SARA Section 311/312, CERCLA/SARA Section 313, OSHA 29 CFR 1910.1200, TSCA. This gasket maker has a working time of one hour.
These RTV gasket makers replace the need for a precut gasket by filling the space between two mating surfaces. They cure in place and are useful for general purpose applications.
These RTV gasket makers replace the need for a precut gasket by filling the space between two mating surfaces. They cure in place and are useful for general purpose applications.
These RTV gasket makers replace the need for a precut gasket by filling the space between two mating surfaces. They cure in place and are useful for general purpose applications.
These RTV gasket makers replace the need for a precut gasket by filling the space between two mating surfaces. They cure in place and are useful for general purpose applications.
To view Availability for another location, please enter postal code below
Availability dates may vary based on the assortment of product in the cart and is not final until you complete your order.
