Non-coolant-through high-speed steel jobber-length drill bits do not have coolant holes, so a separate hose is required to bring coolant to the bits' tip if it is needed. High-speed steel drill bits provide more flexibility and absorb more shock and vibration than cobalt, powdered-metal, and carbide drill bits, making them suitable for use in manual drilling machines and handheld power tools. They may leave a rough finish on the hole. Jobber-length drill bits are the most commonly used drill-bit length. They provide a good balance of strength and accuracy when drilling into a range of materials.
This general purpose jobber length drill bit is made of high speed steel and has a 3/16 inch diameter, 1 3/16 inch long shank. It is for use with aluminum, composite, copper, slate, steel, wood, and meets ANSI standards. This 150B series jobber length drill bit has a bright (uncoated) finish, and has wire measurements. It is non-coolant through with a 3½ inch length. Plus it has two 2 5/16 inch spiral flutes, a straight shank, and 118 Degrees conventional point.
This general purpose jobber length drill bit is made of high speed steel and has a 3/16 inch diameter, 1 3/16 inch long shank. It is for use with aluminum, composite, copper, slate, steel, wood, and meets ANSI standards. This 150B series jobber length drill bit has a bright (uncoated) finish, and has wire measurements. It is non-coolant through with a 3½ inch length. Plus it has two 2 5/16 inch spiral flutes, a straight shank, and 118 Degrees conventional point.
This general purpose jobber length drill bit is made of high speed steel and has a 11/64 inch diameter, 1 3/16 inch long shank. It is for use with aluminum, composite, copper, slate, steel, wood, and meets ANSI standards. This 150B series jobber length drill bit has a bright (uncoated) finish, and has wire measurements. It is non-coolant through with a 3½ inch length. Plus it has two 2 5/16 inch spiral flutes, a straight shank, and 118 Degrees conventional point.
This general purpose jobber length drill bit is made of high speed steel and has a 11/64 inch diameter, 1 3/16 inch long shank. It is for use with aluminum, composite, copper, slate, steel, wood, and meets ANSI standards. This 150B series jobber length drill bit has a bright (uncoated) finish, and has wire measurements. It is non-coolant through with a 3½ inch length. Plus it has two 2 5/16 inch spiral flutes, a straight shank, and 118 Degrees conventional point.
This general purpose jobber length drill bit is made of high speed steel and has a 4.4 mm diameter, 33 mm long shank. It is for use with aluminum, brass, bronze, copper, and meets the standards for DIN 338. This 150D series jobber length drill bit has a bright (uncoated) finish, and has metric measurements. It is non-coolant through with a 80mm length. Plus it has two 47mm spiral flutes, a straight shank, and 118 Degrees conventional point.
This general purpose jobber length drill bit is made of high speed steel and has a 4.4 mm diameter, 33 mm long shank. It is for use with aluminum, brass, bronze, copper, and meets the standards for DIN 338. This 150D series jobber length drill bit has a bright (uncoated) finish, and has metric measurements. It is non-coolant through with a 80mm length. Plus it has two 47mm spiral flutes, a straight shank, and 118 Degrees conventional point.
This general purpose jobber length drill bit is made of high speed steel and has a 5.1 mm diameter, 34 mm long shank. It is for use with aluminum, brass, bronze, copper, and meets the standards for DIN 338. This 150D series jobber length drill bit has a bright (uncoated) finish, and has metric measurements. It is non-coolant through with a 86mm length. Plus it has two 52mm spiral flutes, a straight shank, and 118 Degrees conventional point.
This general purpose jobber length drill bit is made of high speed steel and has a 5.1 mm diameter, 34 mm long shank. It is for use with aluminum, brass, bronze, copper, and meets the standards for DIN 338. This 150D series jobber length drill bit has a bright (uncoated) finish, and has metric measurements. It is non-coolant through with a 86mm length. Plus it has two 52mm spiral flutes, a straight shank, and 118 Degrees conventional point.
This general purpose jobber length drill bit is made of high speed steel and has a 7/64 inch diameter, 1⅛ inch long shank. It is for use with aluminum, composite, copper, slate, steel, wood, and meets ANSI standards. This 150B series jobber length drill bit has a bright (uncoated) finish, and has wire measurements. It is non-coolant through with a 2¾ inch length. Plus it has two 1⅝ inch spiral flutes, a straight shank, and 118 Degrees conventional point.
This general purpose jobber length drill bit is made of high speed steel and has a 7/64 inch diameter, 1⅛ inch long shank. It is for use with aluminum, composite, copper, slate, steel, wood, and meets ANSI standards. This 150B series jobber length drill bit has a bright (uncoated) finish, and has wire measurements. It is non-coolant through with a 2¾ inch length. Plus it has two 1⅝ inch spiral flutes, a straight shank, and 118 Degrees conventional point.
This general purpose jobber length drill bit is made of high speed steel and has a 5.9 mm diameter, 36 mm long shank. It is for use with aluminum, brass, bronze, copper, and meets the standards for DIN 338. This 150D series jobber length drill bit has a bright (uncoated) finish, and has metric measurements. It is non-coolant through with a 93mm length. Plus it has two 57mm spiral flutes, a straight shank, and 118 Degrees conventional point.
This general purpose jobber length drill bit is made of high speed steel and has a 5.9 mm diameter, 36 mm long shank. It is for use with aluminum, brass, bronze, copper, and meets the standards for DIN 338. This 150D series jobber length drill bit has a bright (uncoated) finish, and has metric measurements. It is non-coolant through with a 93mm length. Plus it has two 57mm spiral flutes, a straight shank, and 118 Degrees conventional point.
Ce foret court à usage général en acier rapide a 6,3 mm de dia et une tige de 38 mm de long. Pour l'aluminium, le laiton, le bronze, le cuivre: répond aux normes DIN 338. Ce foret de la série 150D a un fini brillant/non revêtu et est métrique. Il est sans canal de refroidissement et a 101 mm de long. De plus, il a deux cannelures hélicoïdales de 63 mm, une tige droite et un angle de pointe de 118°.
Ce foret court à usage général en acier rapide a 6,3 mm de dia et une tige de 38 mm de long. Pour l'aluminium, le laiton, le bronze, le cuivre: répond aux normes DIN 338. Ce foret de la série 150D a un fini brillant/non revêtu et est métrique. Il est sans canal de refroidissement et a 101 mm de long. De plus, il a deux cannelures hélicoïdales de 63 mm, une tige droite et un angle de pointe de 118°.
Ce foret court à usage général en acier rapide a 7 mm de dia et une tige de 40 mm de long. Pour l'aluminium, le laiton, le bronze, le cuivre. Ce foret de la série 150D a un fini brillant/non revêtu et est métrique. Il est sans canal de refroidissement et a 109 mm de long. De plus, il a deux cannelures hélicoïdales de 69 mm, une tige droite et un angle de pointe de 118°.
Ce foret court à usage général en acier rapide a 7 mm de dia et une tige de 40 mm de long. Pour l'aluminium, le laiton, le bronze, le cuivre. Ce foret de la série 150D a un fini brillant/non revêtu et est métrique. Il est sans canal de refroidissement et a 109 mm de long. De plus, il a deux cannelures hélicoïdales de 69 mm, une tige droite et un angle de pointe de 118°.
Ce foret court à usage général en acier rapide a 5/64 po de dia et une tige de 1 po de long. Pour l’aluminium, le composite, le cuivre, l’ardoise, l’acier, le bois, répond aux normes ANSI. Ce foret de la série 150B a un fini brillant/non revêtu et des mesures de fil. Il est sans canal de refroidissement et est 2 1/8 de po de long. De plus, il a deux cannelures hélicoïdales de 1 1/8 po, une tige droite et un angle de pointe de 118°.
Ce foret court à usage général en acier rapide a 5/64 po de dia et une tige de 1 po de long. Pour l’aluminium, le composite, le cuivre, l’ardoise, l’acier, le bois, répond aux normes ANSI. Ce foret de la série 150B a un fini brillant/non revêtu et des mesures de fil. Il est sans canal de refroidissement et est 2 1/8 de po de long. De plus, il a deux cannelures hélicoïdales de 1 1/8 po, une tige droite et un angle de pointe de 118°.
This general purpose jobber length drill bit is made of high speed steel and has a 3/64 inch diameter, one-inch long shank. It is for use with aluminum, composite, copper, slate, steel, wood, and meets ANSI standards. This 150B series jobber length drill bit has a bright (uncoated) finish, and has wire measurements. It is non-coolant through with a 1⅞ inch length. Plus it has two ⅞ inch spiral flutes, a straight shank, and 118 Degrees conventional point.
This general purpose jobber length drill bit is made of high speed steel and has a 3/64 inch diameter, one-inch long shank. It is for use with aluminum, composite, copper, slate, steel, wood, and meets ANSI standards. This 150B series jobber length drill bit has a bright (uncoated) finish, and has wire measurements. It is non-coolant through with a 1⅞ inch length. Plus it has two ⅞ inch spiral flutes, a straight shank, and 118 Degrees conventional point.
This general purpose jobber length drill bit is made of high speed steel and has a 7.6 mm diameter, 42 mm long shank. It is for use with aluminum, brass, bronze, copper, and meets the standards for DIN 338. This 150D series jobber length drill bit has a bright (uncoated) finish, and has metric measurements. It is non-coolant through with a 117mm length. Plus it has two 75mm spiral flutes, a straight shank, and 118 Degrees conventional point.
This general purpose jobber length drill bit is made of high speed steel and has a 7.6 mm diameter, 42 mm long shank. It is for use with aluminum, brass, bronze, copper, and meets the standards for DIN 338. This 150D series jobber length drill bit has a bright (uncoated) finish, and has metric measurements. It is non-coolant through with a 117mm length. Plus it has two 75mm spiral flutes, a straight shank, and 118 Degrees conventional point.
This general purpose jobber length drill bit is made of high speed steel and has a 8.5 mm diameter, 42 mm long shank. It is for use with aluminum, brass, bronze, copper. This 150D series jobber length drill bit has a bright (uncoated) finish, and has metric measurements. It is non-coolant through with a 117mm length. Plus it has two 75mm spiral flutes, a straight shank, and 118 Degrees conventional point.
This general purpose jobber length drill bit is made of high speed steel and has a 8.5 mm diameter, 42 mm long shank. It is for use with aluminum, brass, bronze, copper. This 150D series jobber length drill bit has a bright (uncoated) finish, and has metric measurements. It is non-coolant through with a 117mm length. Plus it has two 75mm spiral flutes, a straight shank, and 118 Degrees conventional point.
Ce foret court à usage général en acier rapide a 1/32 po de dia et une tige de 15/16 po de long. Pour l’aluminium, le composite, le cuivre, l’ardoise, l’acier, le bois, répond aux normes ANSI. Ce foret de la série 150B a un fini brillant/non revêtu et des mesures de fil. Il est sans canal de refroidissement et est 1 5/8 de po de long. De plus, il a deux cannelures hélicoïdales de 11/16 de po, une tige droite et un angle de pointe de 118°.
Ce foret court à usage général en acier rapide a 1/32 po de dia et une tige de 15/16 po de long. Pour l’aluminium, le composite, le cuivre, l’ardoise, l’acier, le bois, répond aux normes ANSI. Ce foret de la série 150B a un fini brillant/non revêtu et des mesures de fil. Il est sans canal de refroidissement et est 1 5/8 de po de long. De plus, il a deux cannelures hélicoïdales de 11/16 de po, une tige droite et un angle de pointe de 118°.
Ce foret court à usage général en acier rapide a 1/32 po de dia et une tige de 7/8 po de long. Pour l’aluminium, le composite, le cuivre, l’ardoise, l’acier, le bois, répond aux normes ANSI. Ce foret de la série 150B a un fini brillant/non revêtu et des mesures de fil. Il est sans canal de refroidissement, avec une longueur de 1 3/8 po. De plus, il a deux cannelures hélicoïdales de 1/2 po, une tige droite et un angle de pointe de 118°.
Ce foret court à usage général en acier rapide a 1/32 po de dia et une tige de 7/8 po de long. Pour l’aluminium, le composite, le cuivre, l’ardoise, l’acier, le bois, répond aux normes ANSI. Ce foret de la série 150B a un fini brillant/non revêtu et des mesures de fil. Il est sans canal de refroidissement, avec une longueur de 1 3/8 po. De plus, il a deux cannelures hélicoïdales de 1/2 po, une tige droite et un angle de pointe de 118°.
Ce foret court à usage général en acier rapide a 9,1 mm de dia et une tige de 44 mm de long. Pour l'aluminium, le laiton, le bronze, le cuivre: répond aux normes DIN 338. Ce foret de la série 150D a un fini brillant/non revêtu et est métrique. Il est sans canal de refroidissement et mesure 125 mm de long. De plus, il a deux cannelures hélicoïdales de 81 mm, une tige droite et un angle de pointe de 118°.
Ce foret court à usage général en acier rapide a 9,1 mm de dia et une tige de 44 mm de long. Pour l'aluminium, le laiton, le bronze, le cuivre: répond aux normes DIN 338. Ce foret de la série 150D a un fini brillant/non revêtu et est métrique. Il est sans canal de refroidissement et mesure 125 mm de long. De plus, il a deux cannelures hélicoïdales de 81 mm, une tige droite et un angle de pointe de 118°.
This general purpose jobber length drill bit is made of high speed steel and has a 1/32 inch diameter, ⅞ inch long shank. It is for use with aluminum, brass, bronze, cast iron, copper, steel, and meets ANSI standards. This 150 series jobber length drill bit has a black oxide finish, and has wire measurements. It is non-coolant through with a 1⅜ inch length. Plus it has two ½ inch spiral flutes, a straight shank, and 118 Degrees conventional point.
This general purpose jobber length drill bit is made of high speed steel and has a 1/32 inch diameter, ⅞ inch long shank. It is for use with aluminum, brass, bronze, cast iron, copper, steel, and meets ANSI standards. This 150 series jobber length drill bit has a black oxide finish, and has wire measurements. It is non-coolant through with a 1⅜ inch length. Plus it has two ½ inch spiral flutes, a straight shank, and 118 Degrees conventional point.
To view Availability for another location, please enter postal code below
Availability dates may vary based on the assortment of product in the cart and is not final until you complete your order.
