Product ITEM is unavailable. See products from the same category below.
General Purpose Spiral-Point Taps
General purpose spiral-point taps are intended for threading a wide range of materials. The taps have straight flutes with a spiral point that pushes chips in front of the tap as it moves into a hole and out the other side, eventually forcing the chips out of the hole. They create internal threads in through holes and are installed into a toolholder on a machine such as a lathe or CNC machine to operate.
This pipe tap is made of high speed steel and has a 0.194 inch diameter, 1.4960 inch long shank. It meets the standards for ANSI. This 105H series pipe tap has a bright (uncoated) finish, and has pipe measurements. It is non-coolant through, has right hand direction with a 2⅜ inch length. Plus it has two flutes and a straight shank.
This pipe tap is made of high speed steel and has a 0.194 inch diameter, 1.4960 inch long shank. It meets the standards for ANSI. This 105H series pipe tap has a bright (uncoated) finish, and has pipe measurements. It is non-coolant through, has right hand direction with a 2⅜ inch length. Plus it has two flutes and a straight shank.
This hand tap is made of high speed steel and has a 0.194 inch diameter, 1.5730 inch long shank. It meets the standards for ANSI. This 105 series hand tap has an oxide finish, and has pipe measurements. It is non-coolant through, has right hand direction with a 2⅜ inch length. Plus it has two flutes and a straight shank.
This hand tap is made of high speed steel and has a 0.194 inch diameter, 1.5730 inch long shank. It meets the standards for ANSI. This 105 series hand tap has an oxide finish, and has pipe measurements. It is non-coolant through, has right hand direction with a 2⅜ inch length. Plus it has two flutes and a straight shank.
This spiral point tap is made of high speed steel and has a 0.323 inch diameter, 1.8350 inch long shank. It is for use with aluminum, cast iron, steel, and meets ANSI standards. This 105 series spiral point tap has an oxide finish, and has fractional inch measurements. It is non-coolant through, has right hand direction with a 3-5/32 inch length. Plus it has three flutes and a straight shank.
This spiral point tap is made of high speed steel and has a 0.323 inch diameter, 1.8350 inch long shank. It is for use with aluminum, cast iron, steel, and meets ANSI standards. This 105 series spiral point tap has an oxide finish, and has fractional inch measurements. It is non-coolant through, has right hand direction with a 3-5/32 inch length. Plus it has three flutes and a straight shank.
This tap is made of high speed steel and has a 0.255 inch diameter, 1.4930 inch long shank. It is designed for use with steel, and meets the standards for ANSI. This 287 series tap has a bright finish, and has fractional inch measurements. It is non-coolant through, has right hand direction with a 2½ inch length. Plus it has two flutes and a straight shank.
This tap is made of high speed steel and has a 0.255 inch diameter, 1.4930 inch long shank. It is designed for use with steel, and meets the standards for ANSI. This 287 series tap has a bright finish, and has fractional inch measurements. It is non-coolant through, has right hand direction with a 2½ inch length. Plus it has two flutes and a straight shank.
This tap is made of high speed steel and has a 3.58mm diameter, 33 mm long shank. It is designed for use with steel, and meets the standards for ANSI. This 288 series tap has a bright finish, and has metric measurements. It is non-coolant through, has right hand direction with a 49 mm length. Plus it has two flutes and a straight shank.
This tap is made of high speed steel and has a 3.58mm diameter, 33 mm long shank. It is designed for use with steel, and meets the standards for ANSI. This 288 series tap has a bright finish, and has metric measurements. It is non-coolant through, has right hand direction with a 49 mm length. Plus it has two flutes and a straight shank.
This tap is made of high speed steel and has a 0.255 inch diameter, 1.4930 inch long shank. It is designed for use with steel, and meets the standards for ANSI. This 287 series tap has a black oxide finish, and has fractional inch measurements. It is non-coolant through, has right hand direction with a 2½ inch length. Plus it has two flutes and a straight shank.
This tap is made of high speed steel and has a 0.255 inch diameter, 1.4930 inch long shank. It is designed for use with steel, and meets the standards for ANSI. This 287 series tap has a black oxide finish, and has fractional inch measurements. It is non-coolant through, has right hand direction with a 2½ inch length. Plus it has two flutes and a straight shank.
This tap is made of high speed steel and has a 0.194 inch diameter, 1.4960 inch long shank. It is designed for use with steel, and meets the standards for ANSI. This 287 series tap has a black oxide finish, and has pipe measurements. It is non-coolant through, has right hand direction with a 2⅜ inch length. Plus it has two flutes and a straight shank.
This tap is made of high speed steel and has a 0.194 inch diameter, 1.4960 inch long shank. It is designed for use with steel, and meets the standards for ANSI. This 287 series tap has a black oxide finish, and has pipe measurements. It is non-coolant through, has right hand direction with a 2⅜ inch length. Plus it has two flutes and a straight shank.
This tap is made of high speed steel and has a 0.194 inch diameter, 1.4960 inch long shank. It is designed for use with steel, and meets the standards for ANSI. This 287 series tap has a bright finish, and has pipe measurements. It is non-coolant through, has right hand direction with a 2⅜ inch length. Plus it has two flutes and a straight shank.
This tap is made of high speed steel and has a 0.194 inch diameter, 1.4960 inch long shank. It is designed for use with steel, and meets the standards for ANSI. This 287 series tap has a bright finish, and has pipe measurements. It is non-coolant through, has right hand direction with a 2⅜ inch length. Plus it has two flutes and a straight shank.
This tap is made of high speed steel and has a 0.323 inch diameter, 1.8360 inch long shank. It is designed for use with steel. This 287 series tap has a bright finish, and has fractional inch measurements. It is non-coolant through, has right hand direction with a 3-5/32 inch length. Plus it has three flutes and a straight shank.
This tap is made of high speed steel and has a 0.323 inch diameter, 1.8360 inch long shank. It is designed for use with steel. This 287 series tap has a bright finish, and has fractional inch measurements. It is non-coolant through, has right hand direction with a 3-5/32 inch length. Plus it has three flutes and a straight shank.
This tap is made of high speed steel and has a 9.30mm diameter, 50 mm long shank. It is designed for use with steel, and meets the standards for ANSI. This 288 series tap has a bright finish, and has metric measurements. It is non-coolant through, has right hand direction with a 86 mm length. Plus it has three flutes and a straight shank.
This tap is made of high speed steel and has a 9.30mm diameter, 50 mm long shank. It is designed for use with steel, and meets the standards for ANSI. This 288 series tap has a bright finish, and has metric measurements. It is non-coolant through, has right hand direction with a 86 mm length. Plus it has three flutes and a straight shank.
This tap is made of high speed steel and has a 0.255 inch diameter, 1.4930 inch long shank. It is designed for use with steel, and meets the standards for ANSI. This 287 series tap has a bright finish, and has fractional inch measurements. It is non-coolant through, has right hand direction with a 2½ inch length. Plus it has three flutes and a straight shank.
This tap is made of high speed steel and has a 0.255 inch diameter, 1.4930 inch long shank. It is designed for use with steel, and meets the standards for ANSI. This 287 series tap has a bright finish, and has fractional inch measurements. It is non-coolant through, has right hand direction with a 2½ inch length. Plus it has three flutes and a straight shank.
This tap is made of high speed steel and has a 0.367 inch diameter, 1.9960 inch long shank. It is designed for use with steel, and meets the standards for ANSI. This 287 series tap has a bright finish, and has fractional inch measurements. It is non-coolant through, has right hand direction with a 3⅜ inch length. Plus it has three flutes and a straight shank.
This tap is made of high speed steel and has a 0.367 inch diameter, 1.9960 inch long shank. It is designed for use with steel, and meets the standards for ANSI. This 287 series tap has a bright finish, and has fractional inch measurements. It is non-coolant through, has right hand direction with a 3⅜ inch length. Plus it has three flutes and a straight shank.
This tap is made of high speed steel and has a 8.10mm diameter, 40 mm long shank. It is designed for use with steel, and meets the standards for ANSI. This 288 series tap has a bright finish, and has metric measurements. It is non-coolant through, has right hand direction with a 69 mm length. Plus it has three flutes and a straight shank.
This tap is made of high speed steel and has a 8.10mm diameter, 40 mm long shank. It is designed for use with steel, and meets the standards for ANSI. This 288 series tap has a bright finish, and has metric measurements. It is non-coolant through, has right hand direction with a 69 mm length. Plus it has three flutes and a straight shank.
This tap is made of high speed steel and has a 0.141 inch diameter, 1.3150 inch long shank. It is designed for use with steel, and meets the standards for ANSI. This 287 series tap has a black oxide finish, and has pipe measurements. It is non-coolant through, has right hand direction with a two-inch length. Plus it has two flutes and a straight shank.
This tap is made of high speed steel and has a 0.141 inch diameter, 1.3150 inch long shank. It is designed for use with steel, and meets the standards for ANSI. This 287 series tap has a black oxide finish, and has pipe measurements. It is non-coolant through, has right hand direction with a two-inch length. Plus it has two flutes and a straight shank.
This tap is made of high speed steel and has a 0.141 inch diameter, 1.3090 inch long shank. It is designed for use with steel, and meets the standards for ANSI. This 287 series tap has a black oxide finish, and has pipe measurements. It is non-coolant through, has right hand direction with a 1⅝ inch length. Plus it has two flutes and a straight shank.
This tap is made of high speed steel and has a 0.141 inch diameter, 1.3090 inch long shank. It is designed for use with steel, and meets the standards for ANSI. This 287 series tap has a black oxide finish, and has pipe measurements. It is non-coolant through, has right hand direction with a 1⅝ inch length. Plus it has two flutes and a straight shank.
This tap is made of high speed steel and has a 0.141 inch diameter, 1.3110 inch long shank. It is designed for use with steel, and meets the standards for ANSI. This 287 series tap has a black oxide finish, and has pipe measurements. It is non-coolant through, has right hand direction with a 1⅞ inch length. Plus it has two flutes and a straight shank.
This tap is made of high speed steel and has a 0.141 inch diameter, 1.3110 inch long shank. It is designed for use with steel, and meets the standards for ANSI. This 287 series tap has a black oxide finish, and has pipe measurements. It is non-coolant through, has right hand direction with a 1⅞ inch length. Plus it has two flutes and a straight shank.
To view Availability for another location, please enter postal code below
Availability dates may vary based on the assortment of product in the cart and is not final until you complete your order.
